Welch Allyn PROPAQ CS Wartungshandbuch Seite 111
- Seite / 142
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
- Vital Signs Monitor 1
- Contents 3
- Safety summary 5
- Definitions 7
- Evaluated to CSA 601-1 8
- Overview 9
- Warranty service 10
- Technical support services 10
- Recommended service intervals 10
- Monitor controls 13
- Self test and service menus 13
- Service test screens 15
- Functional verification 17
- Required equipment 18
- Safety tests 19
- RIBBED (+) SMOOTH (-) 22
- System tests 23
- Part 1— Visual check 26
- ECG X1000 27
- SYNC OUT 28
- (scope probe) 28
- DEFIB SYNC 28
- 10:42:17 30
- Temperature 31
- Nurse Call 31
- Sensor compatibility 32
- Printer tests 33
- verification preparation 34
- Example 2 35
- (continued) 37
- Mainstream CO 38
- Sidestream CO 40
- verification procedure 40
- ON NETWORK 43
- ARE YOU SURE? 45
- Calibration 47
- Equipment needed 48
- Service Manual Calibration 45 49
- Recharger supply adjustments 50
- Main power supply adjustments 52
- 8. Disconnect the DMM leads 53
- Calibrating realtime ECG out 54
- Invasive Blood Pressure 57
- MSP Board (MCO 58
- ) calibration 58
- Troubleshooting 59
- Non-recoverable error codes 60
- Battery capacity check 61
- Repair procedures 63
- Required tools 64
- Propaq CS Monitor options 65
- Front chassis 66
- Interface chassis 67
- Rear chassis 67
- Replacing the battery pack 68
- Within the European Union 69
- Outside the European Union 69
- Monitor cable 70
- Battery pack 70
- Battery pack cable 70
- Battery pack cover 70
- Opening the monitor 72
- P1 removal 74
- Closing the monitor 76
- Replacing the Analog Board 77
- Replacing the Display 79
- IMPORTANT: 80
- Short screw 80
- Reinstalling the Display 81
- Replacing air tubing 83
- Replacing cables 84
- Replacing PROMs 84
- Cuff fittings 86
- Replacing the Recharger Board 87
- Replacing the pump 89
- Replacing the side panels 90
- Removing the left side panel 91
- Installing side panels 91
- ROUTE CABLE BUNDLE 92
- ALONG BOTTOM OF 92
- REAR CHASSIS 92
- Closing Expansion Module 96
- Replacing the printer 99
- Installing the printer 100
- Opening the SpO 101
- Replacing the SpO 102
- Replacing the MSP/SpO 103
- Replacing the Sidestream CO 104
- Water Trap Receiver 105
- Exhaust Port Hole 105
- Pneumatic Reservoir 105
- Replacing the radio card 107
- Technical overview 109
- Monitor options 110
- Expansion Module 111
- Option 221 111
- SYSTEM BLOCK 114
- Power electronics description 115
- RECHARGER 116
- DIGITAL BOARD 116
- ANALOG BOARD 116
- MONITORING ELECTRONICS 117
- SYSTEM DIAGRAM 117
- NIBP pneumatics description 120
- Cabling diagrams 124
- MOT (0..5) AD (0..7) 126
- Pulse oximetry option (SpO 127
- ) description 127
- PULSE OXIMETRY BLOCK DIAGRAM 129
- Capnography (CO 130
- Mainstream Board 131
- IPC expansion 132
- Power distribution system 132
- analysis chamber (bench) 132
- Special service tools 137
- Manufacturable test equipment 139
- 810-0696-56 141
- 810-0696-57 142
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern