Welch Allyn PROPAQ CS Spezifikationen Seite 64
- Seite / 130
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
60 Alarms & Alerts Welch Allyn Propaq CS Vital Signs Monitor
waveform is displayed without range values. Replace the adapter or replace the
sensor.
LACK OF WAVE - CHECK ADAPTER, SENSOR. Either the airway adapter is
obstructed or the CO
2
sensor has failed. Replace the airway adapter if it is obstructed.
The sensor must be unplugged and plugged in again.
LOW BATTERY - HEATER DISABLED (UNCAL appears in the numerics area). The
monitor’s battery voltage is too low. The CO
2
waveform is displayed without range
values. To continue operation, supply ac power to the monitor.
NO MAINSTREAM SENSOR DETECTED (SRCH appears in the numerics area). The
mainstream CO
2
sensor has been disconnected from the Propaq CS monitor after
providing CO
2
values. Disconnect and reconnect the sensor to the monitor if
necessary.
NON-PROTOCOL SENSOR (UNCAL appears in the numerics area). A CO
2
sensor has
been connected that does not match Welch Allyn’s specifications. The CO
2
waveform
is displayed without range values. Replace the sensor with a Welch Allyn CO
2
sensor.
SENSOR FAILURE - CALIBRATION ERROR. A sensor is defective or out of calibration
and disabled. Replace the sensor.
SENSOR FAILURE - EEPROM. The sensor has failed. Replace the sensor.
SENSOR FAILURE - HEATER. The sensor’s temperature control circuit or the
monitor’s CO2 circuitry has failed. Try replacing the sensor. If the message reappears,
have the monitor serviced.
SENSOR FAILURE - MOTOR DRIVE. The sensor’s motor drive (in the sensor head)
has failed. Replace the sensor.
SENSOR TEMPERATURE TOO HIGH. The sensor’s temperature is too high. The
sensor’s ambient operating range is 10° to 46° C. When the ambient temperature
returns to this range, this message is automatically removed and operation is
restored.
The following messages can appear in the numerics display area.
OFF. No CO2 source is selected.
SRCH. The sensor is preparing for a measurement.
UNCAL. The monitor has detected a problem such as a lack of calibration, an
obstruction, or a low battery.
WARM UP. The sensor heater is warming up. Wait 20 to 30 seconds for the sensor to
heat. Values should appear in the numerics area when the sensor is sufficiently warm.
Sidestream CO
2
messages
ALTIMETER FAILURE - RANGE. The Propaq CS monitor is operating at an altitude
outside the sidestream CO2 option’s operating altitude range of -2,000 to 15,000 feet.
Returning the monitor to within this range automatically cancels this message and
restores operation.
ALTIMETER FAILURE - RATE. The altimeter has detected that the ambient pressure is
changing at a rate greater than 100 mmHg/minute. When the rate of change is back
within the 100 mmHg/minute range, disconnect and reconnect the CO2 sensor to the
monitor.
- Vital Signs Monitor 1
- Contents 3
- General information 5
- General warnings and cautions 7
- Controls and connectors 11
- ECG / EKG RESP 12
- COMPATIBLE 12
- Option connectors 13
- Main Menu 15
- Setup Menus 16
- ? ? ? is displayed 20
- Directions for Use Setup 19 23
- Monitoring 25
- Ω series resistors 26
- ECG bandwidth selected: 29
- MON = Monitor 29
- EXT = Extended 29
- Pacemaker signal indicators 31
- First format 35
- Second format 35
- Take the NIBP reading 37
- Perform SpO 41
- monitoring 41
- “spot-check” monitoring 45
- Perform Mainstream CO 46
- Perform sidestream CO 48
- Set up the CO 50
- display and alarm limits 50
- FLOW RATE is displayed 51
- (not mainstream CO 51
- Alarms & Alerts 53
- 1. P r e s s Silence/Reset 54
- 4 MIN SUSPND 55
- Station messages 57
- Alarm holdoffs 59
- Connect nurse call option 59
- Simultaneous equipment alerts 60
- ECG messages 60
- RESP messages 60
- IBP messages 61
- NIBP messages 61
- Temperature messages 63
- messages 63
- Mainstream CO 63
- Sidestream CO 64
- Program alert message 66
- Printer alert messages 67
- Defibrillator alert message 67
- Printing & trends 69
- Display or print trends 70
- Delete all patient trends 71
- Print OxyCRG 73
- DEFIB SYNCHROMONITOR 77
- EKG x 1000 77
- The Acuity Menu 78
- Directions for Use Acuity 75 79
- Battery charging light 79
- Power input connector 79
- Acuity connector 79
- Press to disconnect 80
- Wireless connection to Acuity 81
- Directions for Use Acuity 79 83
- Maintenance 85
- Green battery charging light 86
- Right Side Panel 86
- Replace power adapter fuses 87
- Install printer paper 89
- Recycling monitor components 91
- Extended storage precautions 92
- Reference 95
- Factory default settings 97
- Specifications 99
- NIBP specifications 103
- Temperature specifications 104
- Pulse oximetry (SpO 105
- ) specifications 105
- Capnography (CO 107
- Alarms specifications 110
- Nurse Call specifications 110
- Trends specifications 111
- Display specifications 111
- Printer specifications 115
- Power Specifications 116
- Power Adapter Specifications 117
- Compliance 119
- European Union 120
- Electromagnetic compatibility 121
- Directions for Use Index 123 127
- Directions for Use Index 125 129
Verwandte Produkte und Handbücher für Nein Welch Allyn PROPAQ CS
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.888 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern